Safety & Use Notice

ECPonics Plant Propagation Capsule

For plant propagation, plant transport, and plant acclimation use only. Not for food, drink, medical, child, or pet use. Not a toy. Keep away from children and pets.

Do not expose to high heat, flame, ovens, microwaves, dishwashers, or direct intense heat. Use only with plants, water, and standard plant substrates. Do not use with pesticides, fertilizers, chemicals, or cleaning products unless those products are properly labeled for plant use and used according to their own instructions.

California Proposition 65 Warning: This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

ECPonics capsules are supplied by Advance To Go Resources LLC / ECPonics. If this capsule was packaged with a live plant by another seller, that seller is responsible for the plant identity, plant care instructions, plant condition, and any plant-related claims.

ECPonics™ Guide

Setup & Use Guide

Select your capsule and your goal to see the correct setup instructions.

Step 1

Select Your Product

Step 2

Select Your Goal

ECPonics SE Sealed Environment

Seed / Germination

Use this mode when starting seeds inside the ECPonics SE.

Phase 1 — Hydrate & Seal

Day 0–7
  • Substrate should be evenly moist; slight pooling at the bottom is okay.
  • Keep the container fully closed.
  • Place in bright indirect light or gentle bottom warmth.
  • Monitor conditions daily.

Phase 2 — Germination Window

Variable
  • Do not disturb seeds.
  • Maintain steady temperature.
  • Condensation inside is expected and beneficial.
  • Opening too early can dry seeds and interrupt germination.

Optional: briefly open for 10–20 minutes only if needed.

Phase 3 — Post-Sprout Stability

Condition Based
  • Wait for seed leaves and first true growth.
  • Look for firm stems and consistent progress.
When the seedling is stable, move to the next appropriate stage.
ECPonics GE SE-Based Variation

Seed / Germination

ECPonics GE is currently based on the ECPonics SE sealed-environment workflow for seed starting.

Phase 1 — Hydrate & Seal

Day 0–7
  • Substrate should be evenly moist; slight pooling at the bottom is okay.
  • Keep the container fully closed.
  • Place in bright indirect light or gentle bottom warmth.
  • Monitor conditions daily.

Phase 2 — Germination Window

Variable
  • Do not disturb seeds.
  • Maintain steady temperature.
  • Condensation inside is expected and beneficial.
  • Opening too early can dry seeds and interrupt germination.

Optional: briefly open for 10–20 minutes only if needed.

Phase 3 — Post-Sprout Stability

Condition Based
  • Wait for seed leaves and first true growth.
  • Look for firm stems and consistent progress.
When the seedling is stable, move to the next appropriate stage.
ECPonics LE SE-Based Variation

Seed / Germination

ECPonics LE is currently based on the ECPonics SE sealed-environment workflow for seed starting.

Phase 1 — Hydrate & Seal

Day 0–7
  • Substrate should be evenly moist; slight pooling at the bottom is okay.
  • Keep the container fully closed.
  • Place in bright indirect light or gentle bottom warmth.
  • Monitor conditions daily.

Phase 2 — Germination Window

Variable
  • Do not disturb seeds.
  • Maintain steady temperature.
  • Condensation inside is expected and beneficial.
  • Opening too early can dry seeds and interrupt germination.

Optional: briefly open for 10–20 minutes only if needed.

Phase 3 — Post-Sprout Stability

Condition Based
  • Wait for seed leaves and first true growth.
  • Look for firm stems and consistent progress.
When the seedling is stable, move to the next appropriate stage.
ECPonics VE Vented Environment

Seed / Germination

Use this mode when starting seeds inside the ECPonics VE.

Phase 1 — Hydrate & Seal

Day 0–7
  • Substrate should be evenly moist; slight pooling at the bottom is okay.
  • Keep the container fully closed, including vents.
  • Place in bright indirect light or gentle bottom warmth.
  • Monitor conditions daily.

Phase 2 — Germination Window

Variable
  • Do not disturb seeds.
  • Maintain steady temperature.
  • Condensation inside is expected and beneficial.
  • Opening vents too early can dry seeds and interrupt germination.

Optional vent opening: 1 vent hole (2 total) for 10–20 minutes, then close again.

Phase 3 — Post-Sprout Stability

Condition Based
  • Wait for seed leaves and first true growth.
  • Look for firm stems and consistent progress.
When the seedling is stable, switch to Acclimation when appropriate.
ECPonics SE Sealed Environment

Cutting / Propagation

Use this mode to root a cutting inside the ECPonics SE.

Phase 1 — Insert & Seal

One-Time Setup
  • Take a healthy cutting.
  • Insert stem into substrate.
  • Ensure at least one node is covered where appropriate.
  • Keep the capsule fully closed.
  • Place in bright indirect light.

Phase 2 — Root Initiation

Species Dependent
  • Do not remove the cutting.
  • Avoid moving the capsule.
  • Stable humidity helps root formation.

Phase 3 — Root Confirmation

Condition Based
  • When the cutting shows resistance, begin gentle transition.
  • Proceed slowly if leaves remain firm.
Once rooted and stable, move to the next growing stage.
ECPonics GE SE-Based Variation

Cutting / Propagation

ECPonics GE currently follows the ECPonics SE sealed-environment workflow for propagation.

Phase 1 — Insert & Seal

One-Time Setup
  • Take a healthy cutting.
  • Insert stem into substrate.
  • Ensure at least one node is covered where appropriate.
  • Keep the capsule fully closed.
  • Place in bright indirect light.

Phase 2 — Root Initiation

Species Dependent
  • Do not remove the cutting.
  • Avoid moving the capsule.
  • Stable humidity helps root formation.

Phase 3 — Root Confirmation

Condition Based
  • When the cutting shows resistance, begin gentle transition.
  • Proceed slowly if leaves remain firm.
Once rooted and stable, move to the next growing stage.
ECPonics LE SE-Based Variation

Cutting / Propagation

ECPonics LE currently follows the ECPonics SE sealed-environment workflow for propagation.

Phase 1 — Insert & Seal

One-Time Setup
  • Take a healthy cutting.
  • Insert stem into substrate.
  • Ensure at least one node is covered where appropriate.
  • Keep the capsule fully closed.
  • Place in bright indirect light.

Phase 2 — Root Initiation

Species Dependent
  • Do not remove the cutting.
  • Avoid moving the capsule.
  • Stable humidity helps root formation.

Phase 3 — Root Confirmation

Condition Based
  • When the cutting shows resistance, begin gentle transition.
  • Proceed slowly if leaves remain firm.
Once rooted and stable, move to the next growing stage.
ECPonics VE Vented Environment

Cutting / Propagation

Use this mode to root a cutting inside the ECPonics VE.

Phase 1 — Insert & Seal

One-Time Setup
  • Take a healthy cutting.
  • Insert stem into substrate.
  • Ensure at least one node is covered where appropriate.
  • Keep the capsule fully closed, including vents.
  • Place in bright indirect light.

Phase 2 — Root Initiation

Species Dependent
  • Do not remove the cutting.
  • Avoid moving the capsule.
  • Stable humidity helps root formation.

Phase 3 — Root Confirmation

Condition Based
  • When you feel slight resistance, open 1 vent hole (2 total).
  • Leave open 15–30 minutes per day, then close again.

Phase 4 — Pre-Acclimation

Optional
  • Once roots are established, open 2 vent holes (4 total).
  • Leave open 1–2 hours per day.
For the safest transition, move next into Acclimation.
ECPonics SE Sealed Environment

Stratification

Use this mode for cold conditioning seeds inside the capsule.

Phase 1 — Prep & Seal

One-Time Setup
  • Seeds should be hydrated in moist substrate, not wet.
  • Keep the capsule fully closed.
  • Place in the refrigerator, not freezer compartment.
  • Do not allow drying.

Phase 2 — Cold Hold

Species Dependent
  • No visible growth is expected during this period.
  • Maintain moisture and avoid temperature cycling.

Phase 3 — Warm Up

Condition Based
  • Remove from refrigerator once complete.
  • Allow the capsule to warm gradually while sealed.
After warming, move into Germination.
ECPonics GE SE-Based Variation

Stratification

ECPonics GE currently follows the ECPonics SE sealed-environment workflow for stratification.

Phase 1 — Prep & Seal

One-Time Setup
  • Seeds should be hydrated in moist substrate, not wet.
  • Keep the capsule fully closed.
  • Place in the refrigerator, not freezer compartment.
  • Do not allow drying.

Phase 2 — Cold Hold

Species Dependent
  • No visible growth is expected during this period.
  • Maintain moisture and avoid temperature cycling.

Phase 3 — Warm Up

Condition Based
  • Remove from refrigerator once complete.
  • Allow the capsule to warm gradually while sealed.
After warming, move into Germination.
ECPonics LE SE-Based Variation

Stratification

ECPonics LE currently follows the ECPonics SE sealed-environment workflow for stratification.

Phase 1 — Prep & Seal

One-Time Setup
  • Seeds should be hydrated in moist substrate, not wet.
  • Keep the capsule fully closed.
  • Place in the refrigerator, not freezer compartment.
  • Do not allow drying.

Phase 2 — Cold Hold

Species Dependent
  • No visible growth is expected during this period.
  • Maintain moisture and avoid temperature cycling.

Phase 3 — Warm Up

Condition Based
  • Remove from refrigerator once complete.
  • Allow the capsule to warm gradually while sealed.
After warming, move into Germination.
ECPonics VE Vented Environment

Stratification

Use this mode for cold conditioning seeds inside the capsule.

Phase 1 — Prep & Seal

One-Time Setup
  • Seeds should be hydrated in moist substrate, not wet.
  • Keep the container fully closed, including vents.
  • Place in the refrigerator, not freezer compartment.
  • Do not allow drying.

Phase 2 — Cold Hold

Species Dependent
  • No visible growth is expected during this period.
  • Maintain moisture and avoid temperature cycling.

Phase 3 — Warm Up

Condition Based
  • Remove from refrigerator once complete.
  • Allow the capsule to warm gradually while sealed.
After warming, move into Germination.
ECPonics VE Vented Environment

Acclimation

Use this mode when your plant arrived already established and needs a gradual transition.

Phase 1 — Seal & Stabilize

Day 0–7
  • Substrate should be evenly moist; slight pooling at the bottom is okay.
  • Keep the capsule fully closed, including vents.
  • Place in bright indirect light.
  • Monitor daily before making changes.

Phase 2 — First Airflow

Day 8–10
  • Open 1 vent hole (2 total).
  • Leave open 30–60 minutes per day.
  • Close vents after each session.

Phase 3 — Increase Airflow

Day 11–14
  • Open 2 vent holes (4 total).
  • Leave open 2–4 hours per day.
  • Close vents after each session.

Phase 4 — Fully Open

Day 15–21
  • Open 5 vent holes (10 total).
  • Leave vents open at least 8 hours per day.
  • Condensation should fade naturally.
Once stable, the plant can move into its longer-term home.
ECPonics GE Grow Environment

Full Growth

Use this mode when growing longer-term inside ECPonics GE instead of using it only for starting or transition.

Phase 1 — Fill & Set

Initial Setup
  • Add clean water to the reservoir area as intended for your GE setup.
  • Keep the root zone supported while avoiding excessive saturation above the lower area.
  • Place in bright light appropriate for the plant.
  • Start with a healthy plant that is already rooted or ready to continue growing.

Phase 2 — Active Growth

Ongoing
  • Monitor water level routinely and refill before the reservoir runs fully dry.
  • Check roots, foliage, and moisture balance regularly.
  • Keep in stable temperatures and avoid harsh direct sun unless the plant is suited for it.

Phase 3 — Maintenance

As Needed
  • Refresh water as needed to keep the system clean.
  • Trim damaged growth and remove any declining material promptly.
  • Move up only when the plant outgrows the capsule or needs a larger long-term setup.
GE is intended for a longer-term grow workflow, not just a short sealed start.
ECPonics LE Light Edition

Full Growth

Use this mode when growing inside ECPonics LE with its dedicated light-based grow workflow.

Phase 1 — Fill, Set & Light

Initial Setup
  • Set the plant and water level correctly for the LE growing setup.
  • Turn on the grow light according to your intended schedule.
  • Keep the capsule in a stable area away from excess heat buildup.
  • Begin with a healthy rooted plant or stable young plant.

Phase 2 — Active Growth Under Light

Ongoing
  • Monitor water level routinely and refill as needed.
  • Watch leaf color, stretch, and overall vigor to judge whether light exposure is appropriate.
  • Keep temperature and airflow balanced so the capsule does not overheat.

Phase 3 — Maintenance & Adjustment

As Needed
  • Adjust the light routine if the plant shows stress or excessive stretching.
  • Refresh water and clean components as needed.
  • Move up only when the plant outgrows the capsule or needs a larger long-term setup.
LE supports a fuller grow method while adding a dedicated light-based workflow.